Please let me know if the port 1521 is default port for the TNSLinstener.
I have a database server on port 1527 how can I make the clients connect on this port or can I have one listener service connect to listen for 2 servers.
Flashing a new firmware by Browser What you need to flash You need the image file you want to flash. To flash a new image, you can use the second stage loader. - Power down the Dreambox, either using “shutdown” and by switching off by the power switch. ) in network press Right arrow on remote Type to On. ´write down key´ on same paper as ser nr and mac address and save it somewhere safe. now you can put in your new patchessoftcamfileschannellists. conect usb stick to spiderbox usb and in menu go to usb and find the extracted file press Ok on it. Settings menu wizard: The first time the decoder will be asked for basic settings. Simple Single Mode Satellite Hot Bird 21 13.0E No Inviare Di SEq C ES: Dual Feed (HOTBIRD ASTRA) Mode config. To list channels go to “Settings” and select your setting ES: DUALFEED / Vhannibal DUALFEED 13-19 East OK 4. Connect the receiver to the LAN with a LAN cable normal; 2. Turn on the receiver while holding down the front of the Q-Box HD MINI; 8. Please read inside the File System archive which version of Boot Image to use and viceversa. Uncompress the file into a blank USB Pen (FAT 32 formatted). All files must be inside the folder “qboxhd_update”.
Connect your Dreambox to a switch/hub/router in your lokal LAN. If you don’t have one, you have to setup an IP address (klick) in the bootloader’s serial setup. look belov how to load new patch after,,,,,(Finished. Set your type of facility ES: One Feed (HOTBIRD) Mode config. Press Menu / Setup Menu / addons, download Add Ons (green button), Duolabs Ok; 3. You may need to restart the decoder (to be performed by the menu! RECOVERY QBOX MINI HD If the decoder does not respond and hangs on boot or reboot constantly must be made to restore the system with one of these ways: Download and install the latest version of the program for Recovery “QBox HD_Updater” from the website way: 1. Scope IMPORTANT NOTE: To void versioning problems make sure the Boot Update and File System Image! To discover the IP address of your QBox please check the LAN configuration See chapters 10.7 and 10.8 Standard parameters are: Login: root Password: qboxhd (low case) At the end press “Save” and you will be directed to the main software window. The most convenient and easy way to update the QBox HD File System Image is via USB Pen in stand-alone mode. Download the latest QBox HD update file and make sure the file you are using has the correct extension 2.
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 or any later version published by the Free Software Foundation.
All logos and trademarks in this document are property of their respective owner.
1the backside of your stb under the power switch, and in some cases also on carton wich it arrived in, you find the ser nr it starts with an I or 1. 3.connect your new Spiderbox with cables such as scart-hdmi ypbpr lnb and networkcable etc: 4. Turn on the receiver while holding down the front of the Q-Box HD MINI; 9. Note: ALL UPDATE PROCEDURES MAY CHANGE ACCORDINGLY WITH DEVELOPMENT IMPROVEMENTS. Boot Update is a hard update and needs to turn OFF and then ON the QBox. Download the latest updating software version can be downloaded from the official web site install it on your PC. Connect the QBox to your network using cross or direct LAN cable.
Note: 서버에서는 "localhost" 및 "localhost:port"를 사용할 때마다 로컬 소켓(윈도우에서는 named pipe)으로 접속을 시도한다. My SQL 클라이언트 라이브러리가 로컬 소켓으로 잘못된 접속을 시도한다면, PHP 환경설정에 있는 항목에 경로를 수정하고, server에 빈 값으로 호출해야 한다.The client only needs to know the hostname of the server to connect) then yes, 1521 is the default and only port.If you are using tnsnames.ora, the Oracle nameserver, or any other method to connec then no, 1521 is not a magic port, is not a default port.Thanks and Regards, Avinash # # This file is written by OFS # on Fri Mar 10 2000 # LISTENER = (ADDRESS_LIST = (ADDRESS= (PROTOCOL= IPC) (KEY= oracle.world) ) (ADDRESS= (PROTOCOL= IPC) (KEY= ORCL) ) (ADDRESS= (PROTOCOL= IPC) (KEY= EXTPROC0) ) (ADDRESS= (COMMUNITY= NMP.world) (PROTOCOL= NMP) (SERVER= SCCPRCI) (PIPE= ORAPIPE) ) (ADDRESS= (PROTOCOL= TCP) (Host= sccprci) (Port= 1521) ) (ADDRESS= (PROTOCOL= TCP) (Host= sccprci) (Port= 1526) ) (ADDRESS= (PROTOCOL= TCP) (Host= 127.0.0.1) (Port= 1521) ) ) SID_LIST_LISTENER = (SID_LIST = (SID_DESC = (GLOBAL_DBNAME = sccprci) (SID_NAME = ORCL) ) (SID_DESC = (SID_NAME = extproc) (PROGRAM=extproc) ) ) CONNECT_TIMEOUT_LISTENER = 10 TRACE_LEVEL_LISTENER = 0 STARTUP_WAIT_TIME_LISTENER = 0 PASSWORDS_LISTENER = (oracle) Fslsccora = (ADDRESS_LIST= (ADDRESS= (PROTOCOL=IPC) (KEY=PRD) ) (ADDRESS= (PROTOCOL=IPC) (KEY=PRD. WORLD) (PROTOCOL=TCP) (Host=SCCORA) (Port=1527) ) ) SID_LIST_Fslsccora = (SID_LIST= (SID_DESC= (SDU=32768) (SID_NAME=PRD) (ORACLE_HOME=E:\orant) (PRESPAWN_MAX=10) ) ) STARTUP_WAIT_TIME_Fslsccora = 0 TRACE_LEVEL_Fslsccora = OFF CONNECT_TIMEOUT_Fslsccora = 10 If you are using "host naming" convention (this is a method that does not require the client to have a file at all.You must be using tcp, you must only have one default database per host.For further clarification, please take a look at the attached file.Also let me know how I can check the names of listeners running on a server (the command).This book is not intended to explain network sniffing in general and it will not provide details about specific network protocols.A lot of useful information regarding these topics can be found at the Wireshark Wiki at https://wiki.wireshark.org/.In this case, 1521 is simply the port used by "convention".The clients would, typically in their tnsnames.ora, connect to the listener on some specified port number.Wireshark is one of those programs that many network managers would love to be able to use, but they are often prevented from getting what they would like from Wireshark because of the lack of documentation.This document is part of an effort by the Wireshark team to improve the usability of Wireshark.The use of mysql connections can become tricky with objects.